Contini Lift table frame ET225E
Questions about Contini Lift table frame ET225E
What would you like to know?
0 questions and answers
Helpful answer
The thing doesn't exactly fly through the ceiling when you adjust the height ;) 38mm/s sounds more plausible
Helpful answer
Yes, mine came with a cable with a Swiss plug
Helpful answer
Try using the "down button" to lower the table as far as it will go. Then possibly unplug the power plug and plug it back in. The error message should then disappear and the lift table should function normally again (including the programmed table level).
Helpful answer
My table was now at its lowest point over the weekend. I tried "everything" possible, but shortly after I asked the question, I was able to find the solution myself. It's typical that it always happens when you've almost given up, isn't it? The solution to my problem was actually quite simple: even when the table was already on the lowest setting, I kept pressing the down button. About 5-10 seconds later, the table went back up a few centimetres. From then on you can release the button and it works again. Sorry for the question, which I was eventually able to answer myself. I hope that this information may help others in a similar situation. Best regards
Helpful answer
For example, this inexpensive part for attaching to the table top (hanging down): LogiLink PC mount from Digitec LogiLink PC mount Various other products, also in other shops (e.g. Schäfer Shop), but all significantly more expensive and in some cases only designed for certain lift table models. good luck!
Try here to see if you can order this cable (special connection to the control box) as a spare part: https://coldtec.ch/service/ Parts list from comparison model: https://static.digitecgalaxus.ch/Files/1/8/6/0/0/4/9/6/100298%20Betriebsanleitung%20Hubtischgestell%20ET203%20.pdf?_gl=1*ki4j8m*_ga*MTExOTQ4MDc1OC4xNjkzNzQ3MzYy*_ga_1EEG883Z43*MTY5Mzc0NzM2Mi4xLjAuMTY5Mzc0NzM2Mi4wLjAuMA...
Top side is 57cm deep, bottom is 67cm.
I have a distance of 1.80m (centre to centre of the legs) for my 2.0m tabletop and have had no problems with it so far. That's already 10 cm more than the description says. A little more is probably possible, about 1.90m I would guess. The feet are 10cm wide, so that would give a gap of 1.80m. I wouldn't recommend more than that, unless you were to screw the frame together even more.
The screws are included in the delivery. However, they eat into the wood, not threaded screws. But you don't have to pre-drill any holes, they go straight in with a cordless screwdriver.
Helpful answer
How quiet?.... As quiet as a Gellette razor or hairdryer :). I am satisfied with it.
Helpful answer
Apart from the color there is no other other diferrence for this model. This is the "updated" model, that differs from the old model by having a different cable tray design underneath.
Helpful answer
Hello, the feet are 68cm deep and symmetrical to the front and back. Kind regards
Helpful answer
It should actually work, but about 8 cm will be lost on both sides (support).
Hello, we have the white model and are happy with it. I don't know if it's different from the grey model - Hello, we have the white model and we are happy with it I don't know if it's different from the grey model.
Helpful answer
I was able to measure it quickly: 1100mm is exactly right. One foot is exactly 550mm wide at the top without the "rail". If you push the rail together completely in the middle at the top, you are at 1100mm.
The minimum width is 1100 mm, the maximum 1800 mm. You can set all dimensions in between, there is no default.
Yes, that works well, we did it that way here too.
I believe the error messages are described here https://www.flexispot.de/support/fehlercodes-und-fehlerbehebung : 5 If the LED display shows "E07" or "E08", please check if the cables and the control box are properly connected. If not, please connect these two components carefully. Then press and hold the "▼" button to reset the unit.
The frame has a maximum width of 180 cm. This means that you would have approx. 40 cm of tabletop on the left and right "outside" the frame. I think this is still within the limits and should therefore be possible.
Length of table top brackets = 580 mm The length of the foot consoles = 680 mm The leg length results from the lifting height.
When the LED display shows "E02", please switch off the desk for 25 minutes. Here you will find all error messages and corresponding solution suggestions: https://de.flexispot.com/support/fehlercodes-und-fehlerbehebung
I think my motor had a technical defect right at the beginning. The two table legs could not be raised synchronously. The frame was picked up and replaced within 5 working days. I found the customer service to be friendly and helpful.
30 of 53 questions