RC receiversavailable in a few days
EUR61,90
Eldat Mini receiver RCL04E5002B01 Easywave 12-24V 2x changeover contact potentiometer IP65
Best products in the RC receivers category
Here's a ranking of the best products in this category. To give you a quick overview, we've also added some key information about the products.
1. Eldat Mini receiver RCL04E5002B01 Easywave 12-24V 2x changeover contact potentiometer IP65
The RCL04 mini-receiver is primarily used in the expansion of existing systems. With its two potential-free relay contacts, a radio interface can be added to a wide variety of systems. It is just as easy to convert a garage door opener as it is to integrate Easywave transmitters into complex door call systems. The RCL04 is operated with 12-24 ACDC and can memorise up to 32 transmission codes. Technically, the RCL04 is identical to the RCL03, except that the housing offers increased protection against dust and water IP65. RCL04E5002B01.
2. Jeti Receiver Rex 7 Assist Jeti duplex
- integrated telemetry: rotation angle on 3 axes, G-Force, temperature - integrated ASSIST stabilization system with stabilization + heading hold + trainer mode - for fixed wing models and multicopters - can output stabilized EX bus signal for e.g. CentralBoxes - supported protocols: PPM, EXBUS, EX,... - programmable functions of the slots - support direct inputs - compact dimensions - 32 bit processor - full range - programmable via the device overview of the Duplex DC/DS transmitters and the JETI Studio from the PC The device files required for setting from the transmitter (device overview) can be found here under the tab Downloads. Please unzip these files and copy them into the Device folder of the transmitter memory.
3. PAJ Allround Finder
In order to use the complete set, a service fee for the data connection and the finder portal is charged. This Allround Finder can only be used in conjunction with the M2M SIM card and the finder portal from PAJ. Both are already included in the scope of delivery. Alarm functions: Alarm on vibration/motion. Alarm when the SOS button is pressed. Alarm when leaving the defined radius. Low battery alarm. Over speed alarm.
Works only on 2G network.
4. FrSky Archer Plus GR8 2.4Ghz receiver
The Archer range of receivers has been expanded with the new Archer Plus series.
The Archer Plus series receivers include several new functions. Firstly, an improved anti-HF interference capability can provide more robust HF performance, in addition to the existing anti-interference performance in the firing process. This Plus series also has two modes, ACCESS and ACCST D16, where the RF protocol is automatically adjusted during the binding process on the radio. With the black box function, some basic flight data (such as voltage and signal) can be easily stored.
The Archer Plus GR8+ with 8 high-precision PWM channels supports full signal strength with two detachable antennas and guarantees optimum antenna reception and range. The GR8+ can be used as a master receiver in a redundant solution by connecting the SBUS input to any other FrSky receiver equipped with an SBUS output. With the FBUS protocol, the Archer Plus series receivers can be easily paired with multiple telemetry devices (XACT servos, ADV sensors, etc.), making it easier to configure the devices.
The Archer Plus GR8+ is a receiver with an improved high-precision variometer that provides the pilot with more accurate and faster altitude and vertical speed data. It also provides more accurate and faster vario audio feedback from your FrSky ACCESS-enabled remote control.
Features:
- Improved anti-HF interference capability with more solid HF performance
- Intelligently tuned ACCESS & ACCST D16 modes
- Supports simple black box functions
- Improved variometer sensor
- 8 high-precision PWM channel outputs
- SBUS Out connector (supports 16CH / 24CH mode)
- SBUS In connector (supports signal redundancy)
- Full reception with telemetry (S.Port or FBUS)
- Anti-interference capability in the ignition process
- Over-The-Air (OTA) FW update*
- Recognition of external battery/device voltage
(*Some functions require ACCESS and ETHOS support).
2202.316.
5. Hitec PCProgrammer
PC ProPC Programmer for HiTEC transmitters, RF modules and receivers Display and record telemetry data on PC.
6. Carson 6-channel receiver model sports
6 channel receiver of Reflex Stick 2 2,4 GHz power supply 4,8 - 6 V plug system Graupner J/R. In combination with the Reflex Stick 2 remote control the system is compatible to MFC, DMD from Tamiya and LR - 634 CU from Carson.
7. Absima Channel receiver
6-channel receiver Absima R6FS 2.4 GHz plug-in system JR / Futaba.
8. Perle ANTENNA 28 mm FOR 2400 MHz WITH CABLE 500 mm AND U.FL-STECKER (MHF)
Zero.
RC receiversavailable in a few days
EUR34,14
Perle ANTENNA 28 mm FOR 2400 MHz WITH CABLE 500 mm AND U.FL-STECKER (MHF)
9. Jeti Receiver REX 10 Jeti duplex
- the new receiver generation - integrated expander for up to 3 sensors - supported protocols: PPM, EXBUS, EX, UDI - programmable functions of the slots - support direct inputs - compact dimensions - 32 bit processor - full range - programmable via the JETIBOX and wireless via the Duplex DC/DS transmitters - internal memory for data logging and control signals (evaluation in preparation) - ideal also in combination with external servo points when connected via Jeti Ex Bus + additional sensors. Sensors - the .bin files required for setting via the device overview of the DC/DS transmitters can be found under the Download tab.
10. Jeti Receiver Rex 10 Assist Jeti duplex
- integrated telemetry: rotation angle on 3-axis, G-Force, temperature - integrated ASSIST stabilization system with stabilization + heading hold + trainer mode - for fixed wing models and multicopters - can output stabilized EX Bus signal for e.g. CentralBoxes - integrated expander for up to 3 sensors - supported protocols: PPM, EXBUS, EX,. - programmable functions of the slots - support direct inputs - compact dimensions - 32 bit processor - full range - programmable via the device overview of the Duplex DC/DS transmitters and the JETI Studio from the PC - antennas with locking pot to increase the input sensitivity (see picture) The device files required for setting from the transmitter (device overview) can be found here under the tab Downloads. Please unzip these files and copy them into the Device folder of the transmitter memory.
